Groups: Registered
Joined: 12/31/2007(UTC)
Posts: 29
Thanks: 8 times
Was thanked: 6 time(s) in 4 post(s)
|
When I open the desktop version of CCR and click on Install Imagine Drivers nothing happens. Literally, NOTHING! Almost as if I didn't click anything. I tried again and again and nothing. I did report it to PC but was wondering if anyone here could help me out. Thanks!
Maureen
|
|
|
|
|
|
Medals:  Groups: Registered, Circle Member
Joined: 2/21/2009(UTC)
Posts: 10,844
Location: Illinois
Thanks: 8631 times
Was thanked: 4374 time(s) in 2913 post(s)
|
Originally Posted by: MaureenAlferez  When I open the desktop version of CCR and click on Install Imagine Drivers nothing happens. Literally, NOTHING! Almost as if I didn't click anything. I tried again and again and nothing. I did report it to PC but was wondering if anyone here could help me out. Thanks!
Maureen Maureen - #1 - Do you have your IMAGINE hooked up to the computer and turned on before you go into CCR? That might help. #2 - ALSO, over on the left menus, under OPTIONS, be sure you have shown CCR that you are using your IMAGINE. #3 - Are you going into the Application, or are you going in via the CUT download? I would go in where you see the CUT option on the mat--which is the download where you see the CUT button. If you're already doing these three things, I don't know what else to suggest. Char
|
|
|
|
|
|
Groups: Registered
Joined: 12/31/2007(UTC)
Posts: 29
Thanks: 8 times
Was thanked: 6 time(s) in 4 post(s)
|
Hi Char!
Thank you so much for your help. OK so I went back to make sure I did steps #1 & #2 and got the same result. As for #3 I opened the desktop application and I do see the cut button on the Imagine screen. I have been able to print but when it's time to cut it simply kicks out the cutting mat and says that my Imagine is either not powered on or is not connected to the computer which it obviously is if it was able to print. I thought this was happening because I haven't installed the Imagine drivers. What do you think?
Maureen
|
|
|
|
|
|
Medals: Groups: Registered, Circle Member
Joined: 2/21/2009(UTC)
Posts: 10,844
Location: Illinois
Thanks: 8631 times
Was thanked: 4374 time(s) in 2913 post(s)
|
Originally Posted by: MaureenAlferez Hi Char!
Thank you so much for your help. OK so I went back to make sure I did steps #1 & #2 and got the same result. As for #3 I opened the desktop application and I do see the cut button on the Imagine screen. I have been able to print but when it's time to cut it simply kicks out the cutting mat and says that my Imagine is either not powered on or is not connected to the computer which it obviously is if it was able to print. I thought this was happening because I haven't installed the Imagine drivers. What do you think?
Maureen Maureen - I think PC must not have this step ready, as yet. I haven't heard of anyone being able to CUT on their IMAGINES since after BUILD 50 (I might be wrong about that, though). Did you go up to the HELP menu when you're in CCR (the download where the CUT button appears?)? If you're on a MAC, you may not have an option to INSTALL DRIVERS, as another poster pointed out in another post. At least, she couldn't see a menu under HELP to install anything. However, on my desktop (WINDOWS XP), there is the option to INSTALL DRIVERS for the Expression, Imagine and E2 under the HELP menu. If you aren't having any better luck than anyone else, I don't think it will hurt to install the Imagine drivers, if you have the capability to do so. Those of us who have, though, can't do anything until PC releases their next "fix" for us. After you install the drivers, be sure to give FEEDBACK to PC--and let them know what you/your computer can/cannot do after you install them. Char Edited by user Wednesday, July 06, 2011 5:00:44 PM(UTC)
| Reason: Not specified
|
|
|
|
|
|
Medals: Groups: Registered, Circle Member
Joined: 10/18/2007(UTC)
Posts: 2,639
Location: Northern Georgia
Thanks: 5122 times
Was thanked: 2163 time(s) in 1098 post(s)
|
Originally Posted by: MaureenAlferez Hi Char!
Thank you so much for your help. OK so I went back to make sure I did steps #1 & #2 and got the same result. As for #3 I opened the desktop application and I do see the cut button on the Imagine screen. I have been able to print but when it's time to cut it simply kicks out the cutting mat and says that my Imagine is either not powered on or is not connected to the computer which it obviously is if it was able to print. I thought this was happening because I haven't installed the Imagine drivers. What do you think?
Maureen My Imagine does this too, but I get no error message. It will print the image but does not cut. Half the time it doesn't recognize my E2 and it never recognizes my cartridges even though they are inserted into the E2. I cannot install the drivers either, even though I have the option to do this.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.