Groups: Registered
Joined: 12/4/2007(UTC)
Posts: 15
|
Anyone know how to adjust speed and pressure on the Imagine when linking with the Gypsy to cut? I am stuck!
Thanks!
|
|
|
|
|
|
Groups: Registered
Joined: 1/5/2010(UTC)
Posts: 772
Location: GEORGETOWN, TX
Thanks: 225 times
Was thanked: 117 time(s) in 92 post(s)
|
NjoyRD wrote:Anyone know how to adjust speed and pressure on the Imagine when linking with the Gypsy to cut? I am stuck!
Thanks! You set it on the Imagine before you cut.
|
|
|
|
|
|
Groups: Cricut Community Moderator, Registered
Joined: 10/28/2009(UTC)
Posts: 1,048
Thanks: 22 times
Was thanked: 796 time(s) in 205 post(s)
|
NjoyRD wrote:Anyone know how to adjust speed and pressure on the Imagine when linking with the Gypsy to cut? I am stuck!
Thanks! In the Project Preview Screen (where the mat is shown) you will see speed and pressure settings in the middle of the screen. You can adjust them there. Chris Provo Craft
|
|
|
|
|
|
Groups: Registered
Joined: 12/14/2006(UTC)
Posts: 21
Location: Madison WI
Thanks: 14 times
Was thanked: 2 time(s) in 2 post(s)
|
I just had this happen last night and couldn't figure out how to do it. With the Expression and Gypsy hook up, I believe you get a message to check pressure and speed but that doesn't appear with the Imagine, right?
|
|
|
|
|
|
Groups: Cricut Community Moderator, Registered
Joined: 10/28/2009(UTC)
Posts: 1,048
Thanks: 22 times
Was thanked: 796 time(s) in 205 post(s)
|
punzie wrote:I just had this happen last night and couldn't figure out how to do it. With the Expression and Gypsy hook up, I believe you get a message to check pressure and speed but that doesn't appear with the Imagine, right? No, I don't think you get that message. Just go into the Settings screen before printing and set it where you want it. Chris Provo Craft
|
|
|
|
|
|
Groups: Registered
Joined: 8/24/2009(UTC)
Posts: 2
|
Ok, I am trying to figure out how to adjust pressure and speed on my Imagine with the Gypsy. I read this post and still not getting it. My settings page on the Imagine has ink status and calibration information. Nothing about pressure or speed. What am I not doing right?
|
|
|
|
|
|
Groups: Cricut Community Moderator, Registered
Joined: 10/28/2009(UTC)
Posts: 1,048
Thanks: 22 times
Was thanked: 796 time(s) in 205 post(s)
|
Originally Posted by: AmyDurocher  Ok, I am trying to figure out how to adjust pressure and speed on my Imagine with the Gypsy. I read this post and still not getting it. My settings page on the Imagine has ink status and calibration information. Nothing about pressure or speed. What am I not doing right? If you are in the Imagine App on your Gypsy then you adjust the pressure and speed just like you would on your Imagine. In the Project Preview screen there are arrows to make these adjustments. Chris Provo Craft
|
|
|
|
|
|
Groups: Registered
Joined: 1/29/2012(UTC)
Posts: 2
|
I have an imagine as well and am looking for this screen everywhere, both on the gypsy and my imagine. I am just not finding it. Did this gal ever get it to work? My paper is tearing constantly. I have changed my blade, sharpened the blade, and even changed the cut on the blade housing to no avail. HELP Please!
|
|
|
|
|
|
Groups: Registered
Joined: 12/9/2007(UTC)
Posts: 129
Thanks: 32 times
Was thanked: 35 time(s) in 22 post(s)
|
The screen before you click on the cut button to cut has the pressure and cut settings. Hope that helps.
|
|
|
|
|
|
Forum Jump
You cannot post new topics in this forum.
You cannot reply to topics in this forum.
You cannot delete your posts in this forum.
You cannot edit your posts in this forum.
You cannot create polls in this forum.
You cannot vote in polls in this forum.